trying to hop things up a little

[torkflight]

well I wanted to keep this quiet for a while but I am getting bored with coming on here and reading nothing so I figured I would show off my new motor a little and tell you what I have planned, I wanted to wait until I was a little further along in the project but I am thinking everyone is getting a little bored so here it is, I wont have this done for at least a couple month's, I am hoping to maybe catch the last few races of the year and maybe hit a cruise or two, I have to make headers, get the dry sump oil system all figured out, do a little fabing with the engine plates, do a little massaging on the firewall to clear the distributer, and I will have to notch out my k-frame a little to clear the dry sump pan, all things considered, I don't think I will have a problem getting it all done by the middle to late summer, I am sure I will run into a few issues but nothing to serious I am sure, so as for the motor, it is a mild street motor, 11.7-1 compression, 358 cubic inch small block, R5 mopar block, P7 mopar heads, jessel belt drive, jessel 1.8 ratio rockers, arrington engines custom grind roller cam, Bryant crank, Carrillo 6" rods, je gas ported pistons, crank is 3.253 stroke, bore is 4.183 with 4.173 pistons 8.875 deck height, cam is 271/279@ 50, 763/770 lift, 108 lobe separation, intake center line degreed to 104.375, like I said, should be a nice little street motor, good rpms, and should perform OK on a 200 horse shot of spray, hopefully I can keep up with ramair, but like I said, I am going more mild for street use, low compression and small cubes

[Red Rocket]

Nice. Looks to be a really nice mild combination. Sure you'll have enough for ramair? It's only 358 cubes...



Looks like the motor plate adapters should be a piece of cake, but the K member might be a little more difficult. Not much spare room there from what I can tell.

[Z28SSMAN]

Nice stuff tork!

[MR.hp]

That should get some attention and I think some of the so called Big Daws around town here night be in a little trouble when you get that out.
As for nobody posting in here I think the car would is a little quiet right now due to the economy.

[torkflight]

As for nobody posting in here I think the car would is a little quiet right now due to the economy.

I hear ya there, I was real scared to spend the money for this motor but it was a deal I couldnt pass up:nos_smile:

[Guest]

damn that is beautiful and rusty all at the same time!

lol
lookin good -

[ramairws6]

Keep up with me? Damn that thing looks pretty sweet actually. Those heads definately look like some high flowing biatchs'!! They ported at all? Who did the build? I suppose you were over at racing junk again and couldn't resist!? Well at least I have someone to race now this summer..........:munchstrechcouch2:

[torkflight]

Keep up with me? Damn that thing looks pretty sweet actually. Those heads definately look like some high flowing biatchs'!! They ported at all? Who did the build? I suppose you were over at racing junk again and couldn't resist!? Well at least I have someone to race now this summer..........:munchstrechcouch2:

yep they are cnc ported, the engine was built by arrington engines, I shouldnt have spent the money but I lowballed and it was at a price I couldnt pass up. hopefully ramair, in the next two months we can line em up.

[ramairws6]

I'll be ready and waiting unless something happens to mine(knocks on wood!)

[ramairws6]

What are the intake/exhaust valve sizes on that bad boy?

[ramairws6]

Oh, top secret I guess?:munchstrechcouch2:

[torkflight]

Oh, top secret I guess?:munchstrechcouch2:

nope, I just dont know, I am trying to get some flow numbers and some specs on these heads, but the guy I am dealing with at arrington is not helping much.

[smooth_358]

i hope you get it running sir, your car made me excited when i was driving around with you guys last fall

[torkflight]

hey ramair, 2.17 intake, 1.64 exhaust, both titanium valves, waiting for an e-mail for some flow numbers.

[Red Rocket]

And let me know when you get those numbers... I'm going to buy that software.